Corner Forms™:

High strength to weight ratio-our CornerForms™ System is made of an extruded industrial grade (tested) plastic, lightweight and easy to apply and re-apply, yet structurally sound!

It is comprised of two principle components: an edge cap to be applied to the panel and a mainform-receiving member. CornerForms™  is stocked in a variety of shapes, colors, and lengths. The factory controlled tolerances make the two component system a "snap" to assemble.

Description: CornerForms™  -fastening forms patent pending (utility) U.S.A. and Canada.
Dimensions: 8' 0" length: additional lengths available upon request.
Shapes: 30°. 45°, 60°, 90°, 120°, 135°. 180°,  4-way connector, "Y" connector, Y-90° connector, finish end cap.

Colors: White, black, gray, and almond
Custom colors available upon request (A total of 150 pieces in any shape combination.)

Cornerforms™

Mainforms and Edgecaps
Degree	Diagram	Dimensions	Finish Option	Price/Add to Cart
45°		96" length	Almond Black Gray White	$39.75
60°		96" length	Almond Black Gray White	$39.75
90°		96" length	Almond Black Gray White	$39.75
120°		96" length	Almond Black Gray White	$39.75
135°		96" length	Almond Black Gray White	$39.75
180°		96" length	Almond Black Gray White	$39.75
Degree	Diagram	Dimensions	Finish Option	Price/Add to Cart
T-CONNECTOR		96" length	Almond Black Gray White	$42.50
Y-CONNECTOR		96" length	Almond Black Gray White	$42.50
FINISH END CAP		96" length	Almond Black Gray White	$26.95
EDGE CAP TX Only		95 1/2" length	Almond Black Gray White	$8.75
ALUMINUM EDGE CAP	(Aluminum)	95 1/2" length	Aluminum	$22.50 two piece minimum
J-MOULD (Finishing Cap)		96" length	Almond Black Gray White	$8.75
DIVISIONAL MOULDING		96" length	Almond Black Gray White	$9.75
INSIDE/OUTSIDE MOULDING		96" length	Almond Black Gray White	$15.35

EXAMPLE IDEA

Wood Substrate
The edge cap is applied to the edge of a 3/4"
panel with 5/8" chisel point staples inserted on
two or three sides 6" on center starting 1/2"
from the top. For additional strength, a standard
approved p. v. c. adhesive can be applied into
the channel of the edge cap.
NOTE: On slatwall panels place the staples
between the slots.
Foam Panel
To secure the edge cap to a "foam" panel,
apply construction grade two sided tape or an
approved adhesive.
NOTE: Some adhesives are not compatible with
"foam" substrate, and we recommend that you
consult with a foam manufacturer or supplier.

Applying Corner Forms™
*Stand panel up
* Open the Corner Forms™ "mouth, and place it
over the edge of the panel. We recommend that
you start at the bottom of the panel.
*Strike the Corner Forms™ with the palm of your
hand at the bottom portion and continue by
working upwards.

 STEP 2

To join "free panel" #B to "stationary panel"
#A, assistance is required.
*Maintain the "stationary panel #A in a secure position
*Tilt #B on edge so the opposite of joining edge is
approximately 6" off the floor
*Insert joining edge into Comer Forms™ "mouth"
* Push Downward into the "mouth" while your assistant
simultaneously strikes Mm back of the Comer Forms
at the point of the panel #B contact Continue upward
as the form snaps over the panel.
NOTE: This procedure is to be used with radius Comer
Forms™ angles, such as 30, 45, 60, 90, 120,
and 135 degrees.